Warenkorb anzeigen (0 Artikel) Mein KontoMerkzettel anzeigenZur Kasse gehen

UreCoat™ /3,99 kg

UreCoat™ ist ein Zweikomponenten-Urethan (A+B), das gemischt und auf eine Vielzahl von Oberflächen gestrichen werden kann, um eine flexible, zähe und stoßfeste Beschichtung zu erhalten.

Das Mischungsverhältnis beträgt 100A:10B nach Gewicht (Grammwaage erforderlich), die Topfzeit beträgt 8 Minuten, die Überstreichzeit 30 Minuten, die klebfreie Zeit 2 Stunden und die vollständige Aushärtung 16 Stunden bei 23°C.

UreCoat™ enthält keine Phthalate oder VOCs.

Eigenschaften

- Haftfähig -
UreCoat™ haftet auf vielen Oberflächen und kann als flexible Beschichtung für expandiertes Polystyrol (EPS-Schaum), Gewebe, einige Metalle und Kunststoffe, Holz, Seile (zur Herstellung von Lianen für Zooausstellungen) und vieles mehr verwendet werden.

- Stark - Ausgehärteter Gummi ist zäh und UV-beständig. UreCoat™ wurde verwendet, um beschädigte oder verschlissene Latexhäute, Masken usw. von Animatronics zu reparieren.

- Farbneutral - Verwendung als flexible Farbgrundlage: UreCoat™ lässt sich leicht mit den Farbstoffen SO-Strong™, UVO™ oder Ignite™ einfärben, um eine dauerhafte Farbe für die Beschichtung von ausgehärteten Smooth-On Urethan-Kautschuken oder Weichschaumstoffen zu schaffen. Ausgehärtetes UreCoat™ wird sich mit dem Gummi- oder Schaumstoffteil biegen und biegen.

sofort ab Lager

99,10 EUR

incl. 21% USt. zzgl. Versand
Gewicht: 5 kg
set (A+B)


Instructions

Amount to Mix and Apply at One Time - Because this is a coating, a small amount goes a long way. Mix only what you can comfortably brush on to your target surface in 8 minutes before material sets up.

Measuring and Mixing - Before you begin, pre-mix Part B thoroughly to re-disperse components that may have settled. A gram scale is required to accurately measure 100 Parts A to 10 Parts B. After dispensing into a mixing container, mix thoroughly for 2 - 3 minutes using a square edged mixing stick. Aggressively scrape the sides and bottom of the mixing container several times. Use the square edge of the stick to bring material off of the sides of the container and blend.

Extending Working Time - Reduce the mass of the mixture to increase working time. Example: layer two sheets of aluminum foil together and create a single-use flat tray with vertical sides to contain the liquid. After mixing parts A and B, pour mixture into the aluminum foil to reduce the mass. Your working time will be significantly increased. Applying - Apply a thin layer to the surface, making sure there are no brush strokes. Wait 30 minutes for material to partially cure and apply a second layer. Subsequent layers can be added as desired.

Thinning - To thin UreCoat™, the recommended mix ratio is 100 Parts A + 10 Parts B + 25 or more Parts of 99% isoprpyl alcohol or acetone depending on the application. Pre-mix solvent into Part A before adding Part B. Observe all safety precautions when handling solvents. Mix thoroughly to a uniform color (no streaks).

Thickening - UreCoat™ can be thickened to a paste-like consistency for brushing or troweling onto surfaces. Ure-Fil™ 11 is an effective filler for thickening this material. The recommended maximum filler load when using Ure-Fil™ 11 is 100 parts UreCoat™ Part A to 10 parts UreCoat™ Part B to 15 parts filler by weight. Ensure filler is dry, and pre-mix filler with Part A before combining with Part B.

Surface Finish - UreCoat™ will cure with a high gloss surface finish. If a matte surface finish is desired, we have two recommended techniques; once UreCoat™ gels or partially cures (30 – 60 minutes after applying), lightly wipe surface with a lint-free cloth that will not shed fibers or a lightly brush surface with a soft paint brush. Do not wait until material is fully cured. Another option is to lightly dust the surface of partially cured UreCoat™ with powdered sugar. Once UreCoat™ is fully cured, the powdered sugar can be washed away with water, leaving a matte surface finish.

Curing - Allow UreCoat™ to cure overnight (at least 16 hours) at room temperature 23°C before handling. Full cure time can be reduced heating the material 60°C for 4 hours. Allow UreCoat™ to come to room temperature before handling. Clean Up - Gently scrape as much uncured material from surface as possible with flat edge tool. Remove remaining uncured UreCoat™ with alcohol.

Hilfe bei der Auswahl

Produkte nach Anwendung sortiert, z. B.:Lifecasting, Bildhauerei, Gießen, Special FX Make-up, Zahnprothesen Special FX, Studium.

FormX Newsletter FormX Mitteilungsblatt Über uns Kontakt Transportoptionen Kundenprojekte AGB Wir haben offene Stellen Anwendungsbereich Branches FormX Academy

Ihr One-Stop-Shop für 3D-Modelling-Materialien

Wir verwenden Cookies um unsere Website zu optimieren und Ihnen das bestmögliche Online-Erlebnis zu bieten. Mit dem Klick auf "Alle akzeptieren" erklären Sie sich damit einverstanden. Erweiterte Einstellungen